|
Sprockets > T8F (8mm) Chain Sprockets
T8F (8mm) Chain Sprockets
T8F (8mm) Chain Sprockets for Motors
|
Nut and Washer for
8mm Left Hand Thread Motor Shafts
Sprocket nut and washer set for most electric scooter motors. Fits left hand
threaded 8mm motor shaft ends. Compatible with MY1016, MY1020, MY6812, and ZY1020
electric motors. Item # SPR-NW8
|
$1.95
|
|
Lock Nut and Washer for 8mm Left Hand Thread Motor Shafts
Sprocket lock nut and washer for motors with 8mm left hand threaded
shaft ends. Fits MY1016, MY1020, and ZY1020 motors. Fits 6812, MY6812, and
MY6812B motors with 9 or more tooth sprockets. Item # SPR-NW8-LK
|
$2.49
|
|
Nut with Built-In Lock Washer for 11mm ID Keyed Motor Shaft Sprockets
Motor shaft nut for keyed 11mm ID sprockets with 4mm wide x 2mm deep keyways.
Left hand threads.
Compatible with SPR-825 sprocket listed below.
Item # NUT-8RW
|
$0.95
|
|
Sprocket Spacer Washer for 11mm ID Keyed Motor Shaft Sprockets
11mm ID x 20mm OD x 1mm thick. Commonly used on gear motors with 11mm shafts when replacing a sprocket with a 13.75mm hub width with a sprocket that has a 9mm or 10mm hub width.
Item # HDW-11X20X1
|
$0.50
|
|
4mm x 4mm x 8mm Key Pin for Keyed Motor Shaft Sprockets
4mm x 4mm x 8mm key pin for sprockets with 4mm wide x 2mm deep keyways.
Compatible with SPR-825 sprocket listed below.
Item # KEY-448
|
$0.95
|
|
9 Tooth 10mm Double D-Bore Sprocket for T8F (8mm) Chain
26mm (1") OD, 10.1mm x 8.6mm ID, 4mm thick. Fits 10mm motor
shafts that have a 10mm x 8.5mm dual-flatted sprocket mounting area with a nut and washer on end to secure sprocket in place.
Made from hardened steel with a black oxide finish. Compatible with MY1020 and ZY1020 electric motors.
Item # SPR-809E1
Compatible with MY1020 motors.
|
$9.95
|
|
10 Tooth 10mm Double D-Bore Sprocket for T8F (8mm)
Chain
29mm (1-1/8") OD, 10.1mm x 8.6mm ID, 4mm thick. Fits 10mm motor
shafts that have a 10mm x 8.5mm dual-flatted sprocket mounting area with a nut and washer on end to secure sprocket in place.
Made from hardened steel with a black oxide finish. Compatible with MY1020 and ZY1020 electric motors.
Item # SPR-810E1
Compatible with MY1020 motors.
|
$9.95
|
|
11 Tooth 10mm Double D-Bore Sprocket for T8F (8mm) Chain
31.5mm (1-1/4") OD, 10.1mm x 8.6mm ID, 4mm thick. Fits 10mm motor shafts that
have a 10mm x 8.5mm dual-flatted sprocket mounting area with a nut and washer on end
to secure sprocket in place. Made from hardened steel with a black oxide finish. Compatible with MY1020 and ZY1020 electric motors.
Item # SPR-811E1
Compatible with MY1020 motors.
|
$9.95
|
|
11 Tooth 8mm D-Bore Sprocket for T8F (8mm) Chain
31.5mm (1-1/4") OD, 8.1mm x 7.1mm ID, 4mm thick. Fits motor shafts that
have a 8mm x 7mm D-bore sprocket mounting area with a nut and washer on end to
secure sprocket in place. Made from hardened steel with a black oxide finish.
Item # SPR-811D2
|
$9.95
|
|
11 Tooth Pinion Sprocket for T8F (8mm) Chain
31.5mm (1-1/4") OD, 14mm ID between bottoms of pinion teeth, 10.5mm ID
between tops of pinion teeth. Made from hardened steel with a black oxide
finish. Fits gear boxes with 14mm OD six tooth pinion shafts.
Item # SPR-811P1
|
$9.95
|
|
12 Tooth 10mm Double D-Bore Sprocket for T8F (8mm) Chain
34mm (1-5/16") OD, 10.1mm x 8.6mm ID, 4mm thick. Fits 10mm motor shafts that
have a 10mm x 8.5mm dual-flatted sprocket mounting area with a nut and washer on end
to secure sprocket in place. Made from hardened steel with a black oxide finish. Compatible with MY1020 and ZY1020 electric motors.
Item # SPR-812E1
Compatible with MY1020 motors.
|
$9.95
|
|
13 Tooth 10mm Double D-Bore Sprocket for T8F (8mm) Chain
36mm (1-7/16") OD, 10.1mm x 8.6mm ID, 4mm thick. Fits 10mm motor shafts that
have a 10mm x 8.5mm dual-flatted sprocket mounting area with a nut and washer on end
to secure sprocket in place. Made from hardened steel with a black oxide finish. Compatible with MY1020 and ZY1020 electric motors. Item # SPR-813E1
Compatible with MY1020 motors.
|
$9.95
|
|
15 Tooth 10mm Double D-Bore Sprocket for T8F (8mm) Chain
42mm (1-11/16") OD, 10.1mm x 8.6mm ID, 4mm thick. Fits 10mm motor shafts that
have a 10mm x 8.5mm dual-flatted sprocket mounting area with a nut and washer on end
to secure sprocket in place. Made from hardened steel with a black oxide finish. Compatible with MY1020 and ZY1020 electric motors. Item # SPR-815E1
Compatible with MY1020 motors.
|
$9.95
|
|
17 Tooth Pinion Sprocket for T8F (8mm) Chain
47mm (1-7/8") OD, 14mm ID between bottoms of pinion teeth, 10.5mm ID between
tops of pinion teeth. Made from hardened steel with a black oxide finish. Fits gear
boxes with 14mm OD six tooth pinion shafts.
Item # SPR-817P1
|
$9.95
|
T8F (8mm) Wheel Mount Chain Sprockets
T8F (8mm) Freewheel Mount Chain Sprockets with F4 Mounting Pattern
Freewheel Clutches
Freewheels with Right Hand Clockwise Threads
1.375" x 24 TPI CW Threads
|
Rear Wheel Freewheel Clutch (Right Side)
4-hole bicycle freewheel clutch with 1.375" x 24 TPI right hand (clockwise) threads. F4 sprocket mounting pattern.
This freewheel has four notches for installation and removal with a freewheel
tool (listed below). Freewheel engages in the clockwise directions. 3-1/16" OD x 1-11/32" ID. Works with 2-1/8"
(54mm) ID chain sprockets with four bolt mounting pattern. Adjacent mounting bolt holes are spaced 47mm (1.85") apart from center to center. Fits 34mm (1.34") OD threaded wheel hubs. 34mm (1.34") ID. M35x1.00 right-hand threads.
Item # FWM-175 |
$14.95
|
Freewheels with Left Hand Counterclockwise Threads
Sprocket Hardware
|
6mm x 20mm Sprocket, Wheel, and Motor Hex Socket Head Bolt
6mm hex socket head bolt that is compatible with many rear wheel sprockets,
one and two piece wheels, and motors. This bolt has 20mm long M6x1.0 right-hand clockwise threads.
Item # HDW-B620
|
$0.50
|
|
Freewheel and Brake to Threaded Wheel Hub Spacer with 35mm ID
Freewheel and brake to threaded wheel hub spacer. Works with both M35x1.00 and 1.375"
x 24 TPI freewheels. 35mm ID, 42mm OD, 2.5mm thick. Made from yellow zinc plated steel.
Item # HDW-3525
Installation Example
|
$1.95
|
Freewheel to Axle Adapters
For Metric Diameter Axles
1.375" x 24 TPI CW Threads
|
Freewheel to Axle Adapter with Right Hand Threads for 20mm Axle
Freewheel adapter with 1.375" x 24 TPI right hand (counterclockwise)
threads. 20mm ID, 0.9" wide, 6mm keyway, Two set screws, Made from zinc plated
steel. Compatible with 16-tooth freewheel item number FWM-180 sold above.
Item # FWM-ADAPTER20
|
$24.95
|
1.375" x 24 TPI CW Threads
|
Freewheel to Axle Adapter with Right Hand Threads for 15mm Axle
Freewheel adapter with 1.375" x 24 TPI right hand clockwise threads.
15mm ID,
0.9" wide, 4mm keyway, Two set screws, Made from zinc plated steel. Compatible
with 16-tooth freewheel item number FWM-180 sold above.
Item # FWM-ADAPTER15
|
$24.95
|
|
4mm x 4mm x 25mm Axle Key
4mm x 4mm x 25mm steel axle key for freewheel to axle adapters with 4mm keyway.
Item # KEY-4425
|
$0.95
|
|
6mm x 6mm x 25mm Axle Key
6mm x 6mm x 25mm steel axle key for freewheel to axle adapters with 6mm keyway.
Item # KEY-6625
|
$0.95
|
For Standard Diameter Axles
1.375" x 24 TPI CW Threads
|
Freewheel to Axle Adapter with Right Hand Threads for 1" Axle
Freewheel adapter with 1.375" x 24 TPI right hand clockwise threads. 1" ID,
0.9" wide, 1/4" keyway, Two set screws, Made from zinc plated steel. Compatible
with 16-tooth freewheel item number FWM-180 sold above.
Item # FWM-ADAPTER1
|
$24.95
|
1.375" x 24 TPI CW Threads
|
Freewheel to Axle Adapter with Right Hand Threads for 3/4" Axle
Freewheel adapter with 1.375" x 24 TPI right hand clockwise threads.
3/4" ID,
0.9" wide, 3/16" keyway, Two set screws, Made from zinc plated steel. Compatible
with 16-tooth freewheel item number FWM-180 sold above.
Item # FWM-ADAPTER3
|
$24.95
|
1.375" x 24 TPI CW Threads
|
Freewheel to Axle Adapter with Right Hand Threads for 5/8" Axle
Freewheel adapter with 1.375" x 24 TPI right hand clockwise threads.
5/8" ID,
0.9" wide, 3/16" keyway, Two set screws, Made from zinc plated steel. Compatible
with 16-tooth freewheel item number FWM-180 sold above.
Item # FWM-ADAPTER8
|
$24.95
|
|
3/16" x 3/16" x 1" Axle Key
3/16" x 3/16" x 1" steel axle key for freewheel to axle adapters with 3/16" keyway.
Item # KEY-316X1
|
$0.95
|
|
1/4" x 1/4" x 15/16" Axle Key
1/4" x 1/4" x 15/16" steel axle key for freewheel to axle adapters with
1/4" keyway.
Item # KEY-104X1516
|
$0.95
|
Freewheel Clutch Tools
Custom-Made Sprockets for 8mm (T8F) Chain
If you need a wheel or axle sprocket that is not listed on this page
then custom-made sprockets can be inquired about on our
Custom-Made Sprockets Page.
|