Parts  Repair Help  Contact Us  Shopping Cart  My Account  Projects 

Sprockets > Jackshaft Kits and Parts / #408 and #410 Sprockets > Jackshaft Kits and Parts for #410 (1/2" x 1/8") Chain

Jackshaft Kits and Parts for #410 (1/2" x 1/8") Chain

Jackshaft Kits and Parts for #40, #41, and #420 Chain

Assembled jackshaft kit with 4-1/2" jackshaft shown above.

 

Jackshaft Kits and Parts

Jackshaft Kits

Jackshaft Parts

Jackshaft Kits




Jackshaft Kit with 15 Tooth and 20 Tooth Sprockets for #410 (1/2" x 1/8") Chain
Weld-on jackshaft kit with 15 tooth and 20 tooth sprockets for a 25% increase or decrease in gear ratio. 4-1/2" long or 10" long 5/8" OD jackshaft with keyway. 15 tooth and 20 tooth sprockets with keyways, two keys, two precision sealed ball bearings with snap rings, two weld-on bearing hangers, and two axle collars with set screws. This is a complete kit that contains everything needed to install a weld-on jackshaft.

Item # JST-410152004 (4-1/2" Jackshaft)

Item # JST-420152010 (10" Jackshaft)

With 4-1/2" Jackshaft

$114.95


With 10" Jackshaft

$119.95





Jackshaft Kit with 15 Tooth and 25 Tooth Sprockets for #410 (1/2" x 1/8") Chain
Weld-on jackshaft kit with 15 tooth and 25 tooth sprockets for a 40% increase or decrease in gear ratio. 4-1/2" long or 10" long 5/8" OD jackshaft with keyway. 15 tooth and 25 tooth sprockets with keyways, two keys, two precision sealed ball bearings with snap rings, two weld-on bearing hangers, and two axle collars with set screws. This is a complete kit that contains everything needed to install a weld-on jackshaft.

Item # JST-410152504 (4-1/2" Jackshaft)

Item # JST-410152510 (10" Jackshaft)

With 4-1/2" Jackshaft

$119.95


With 10" Jackshaft

$124.95


Jackshafts Parts
All of the jackshaft parts sold below are 100% compatible and interchangeable with each other and are the same parts used to make the jackshaft kits sold above.

Jackshaft Sprockets


15 Tooth 5/8" Bore Sprocket for #410 (1/2" x 1/8") Chain
2.65" OD, 5/8" ID. Keyway for 3/16" x 3/16" key. Two set screws. One set screw on keyway and the other 90 degrees from keyway. Made from high-carbon steel with hardened teeth and a black oxide or zinc plated finish.
Item # SPR-41015J
$29.95


20 Tooth 5/8" Bore Sprocket for #410 (1/2" x 1/8") Chain
3.15" OD, 5/8" ID. Keyway for 3/16" x 3/16" key. Two set screws. One set screw on keyway and the other 90 degrees from keyway. Made from high-carbon steel with hardened teeth and a black oxide or zinc plated finish.
Item # SPR-41020J
$34.95


25 Tooth 5/8" Bore Sprocket for #410 (1/2" x 1/8") Chain
4.25" OD, 5/8" ID. Keyway for 3/16" x 3/16" key. Two set screws. One set screw on keyway and the other 90 degrees from keyway. Made from high-carbon steel with hardened teeth and a black oxide or zinc plated finish.
Item # SPR-41025J
$39.95

Jackshafts


5/8" OD x 4-1/2" Long Jackshaft
5/8" OD x 4-1/2" long steel jackshaft with keyway for 3/16" x 3/16" key. Made from high-carbon steel with a black oxide finish.
Item # JST-5804

$14.95


5/8" OD x 10" Long Jackshaft
5/8" OD x 10" long steel jackshaft with keyway for 3/16" x 3/16" key. Made from high-carbon steel with a black oxide finish.
Item # JST-5810

$19.95

Jackshaft Keys


3/16" x 3/16" x 1/2" Jackshaft Key
3/16" x 3/16" x 1/2" zinc plated steel jackshaft key. This part goes between the sprocket and jackshaft to secure them from rotating against each other.
Item # KEY-316X05

$0.95

Jackshaft Bearings


Sealed Bearing for Jackshafts with 5/8" Axle
1-3/8" OD x 5/8" ID x 7/16" thick. Includes snap ring. Pre-lubricated with bearing grease. Two rubber seals keep out dust, dirt, moisture, and water. Precision ground and hardened bearing components for extended service life under demanding conditions.
Item # JST-B58138
$4.95


Bolt-On Bearing Hanger with Sealed Bearing for 5/8" OD Axle
Cast iron bearing hanger with sealed bearing for 5/8" OD jackshafts. Bearing collar has two setscrews to hold jackshaft or axle in place. Bearing pivots inside bearing holder for self-alignment so precise alignment of jackshaft and bearing hanger is not necessary. Pre-lubricated and has a grease fitting for relubrication. Mounting bolt holes suitable for 7/16" or 10mm bolts. Length 4.85" (123mm), Width 1.28" (32.3mm), Height 2.2" (56mm). Precision ground and hardened bearing components for extended service life.
Item # JST-H206
$11.95

Jackshaft Bearing Hangers


1-3/8" ID Jackshaft Bearing Hanger
1-3/8" ID x 3" OD x 1/4" thick jackshaft bearing hanger with 2" flat mounting edge. For weld-on applications. Made from high-strength steel with no surface finish so it is ready to weld.
Item # JST-H138

$7.95

Jackshaft Collars


5/8" ID Jackshaft Collar
5/8" ID x 1-1/8" OD x 1/2" wide zinc plated steel jackshaft collar with set screw.
Item # JST-C5805

$1.95

 

Related Items: Online Gear Ratio Calculator for Jackshafts



"When you need Electric Scooter Parts, go to: ElectricScooterParts.com"

 

Store Polices | Electric Scooter Repair Help | Dealer Discounts | Feedback | About Us

 

We Ship Internationally

             
Copyright© 2002-2020 by ElectricScooterParts.com, an Electricruz Inc. company. All rights reserved.