• Port and Pin Numbers: The port and pin numbers are usually embossed or imprinted on the plug-in end of the battery charger connector.

• 2-Port Inline - 2-port inline connectors are used on some versions of Rad-2-Go and Zappy scooters plus a handful of other Chinese-made electric scooter brands.

• 3-Port Inline - 3-port inline connectors are by far the most common type of battery charger connectors used on electric scooters. They are used on most Chinese-made electric scooters and bikes including the following brands: Razor, Rad-2-Go, Boreem, E-Scooter, Scoot-N-Go, Sunl, Terminator, X-Treme, plus many others.

• 3-Pin XLR - 3-pin XLR connectors are commonly used on 12 Volt, 24 Volt, and 36 Volt electric scooters. They are used on the following scooter brands: eZip, IZIP, Currie, Schwinn, GT, Mongoose, Lashout, Xcaliber, Bladez, E-Boarder, Tomb Raider plus many others.

• 4-Pin XLR - 4-pin XLR connectors are used on newer models of eZip and IZIP 24 Volt and 36 Volt electric scooters and bicycles.

• 3-Port House - 3-port house connectors are used on a large number of 36 Volt, 48 Volt, and 60 Volts electric scooters including Electra® Voy, Tao Tao, Baja, X-Treme, Rad-2-Go, EVT, and E-Road plus many other brands.

• 3-Port House for Panterra and Gio - 3-port house connectors for Panterra and Gio electric scooters have reverse polarity from standard electric scooters.

• 3-Pin House - 3-pin house connectors are used on HCF Cute 002, Cute 301, and Cute 302 and electric scooters.

• Polarized C7 - Polarized C7 connectors are used on the City Bug E2 and Razor 132E electric scooters.

• Coaxial - Coaxial connectors are most commonly used on smaller child-sized 12 Volt and 24 Volt scooters including Pulse, Razor, E-Scooter plus many others.

• RCA - RCA connectors are commonly used on 24 Volt, 36 Volt, and 48 Volt electric scooters and bicycles. They are used on both lead acid battery and lithium battery chargers however the trend is for them to be used primarily on lithium battery charger.

• Polarized - Polarized connectors are used on some older model 12 Volt electric scooters. They are used on Zappy (Zap) Classic electric scooters and bikes and Sunpex E-Boarder electric scooters.

We can install any connector plug on any battery charger. If the connector that you need is not listed with the battery charger that you need then please give us a call to special order it.

• Always plug the battery charger into the electric scooter, bike, or go kart before plugging into wall outlet. When charging is complete unplug charger from wall outlet before unplugging from scooter or bike.

• To get the most life out of your batteries recharge them as soon as possible after every ride, even very small rides. Leaving a scooter battery in a partially discharged state lowers the useful life of the battery.

• When a an electric scooter, bike, or go kart is in storage or not being used frequently recharge the batteries at least every 30 days.

• The battery chargers sold on this page are designed for SLA (Sealed Lead-Acid) batteries. Any brand of SLA battery charger may be used on any electric scooter, bike, or go kart that uses SLA batteries as long as the Voltage, Amperage, Connector, and the connectors Pin Polarities are the same as the vehicles original battery charger.

• The Amperage of the battery charger may be decreased for longer battery life, or increased for a quicker recharge time. (see charging rate chart below)

• Automatic SLA battery chargers are designed so that they can and will not charge defective SLA batteries. This is a safety feature. If a defective SLA battery is attempted to be charged it could overheat and melt or damage the equipment that it is located in.

• Good SLA batteries bounce back above their rated Voltage level within a few minutes after being discharged. If a SLA battery's Voltage does not bounce back above its rated Voltage level within a few minutes after being discharged then it is usually considered defective or worn out.

• Sometimes riders and rental stores want to use their electric scooters, bikes, or go karts for more than one battery cycle per day so they use battery chargers with a higher Amp rating than the electric scooters original battery charger. These quick rate battery chargers are typically rated in the 3 Amp through 6 Amp power output range and recharge most electric scooter battery packs in 2-3 hours, however they will slightly lower the longevity of the battery pack when compared to using a slow rate battery charger.

• To preserve the life of the batteries use a slow rate battery charger whenever possible. If a scooter is driven for more than one battery cycle per day then using a smaller battery charger overnight, and a larger battery charger during the day is the best solution.

• Do not use automotive or motorcycle battery chargers to charge SLA batteries. These type of battery chargers are designed for charging wet cell lead-acid batteries and if used on SLA batteries may cause permanent damage to the battery and equipment due to overcharging and overheating.

12 Volt
5-8 Ah Pack

12 Volt
9-15 Ah Pack

12 Volt
5-9 Ah Pack

24 Volt
5-9 Ah Pack

24 Volt
9-15 Ah Pack

24 Volt
17-22 Ah Pack

slow rate:
12V 1A
quick rate:
12V 2A

slow rate:
12V 1.5A
quick rate:
12V 3A

slow rate:
12V 3A
quick rate:
12V 6A

slow rate:
24V 1A
quick rate:
24V 2A

slow rate:
24V 1.5A
quick rate:
24V 3A

slow rate:
24V 3A
quick rate:
24V 6A

36 Volt
5-8 Ah Pack

36 Volt
9-15 Ah Pack

36 Volt
17-22 Ah Pack

48 Volt
5-8 Ah Pack

48 Volt
9-15 Ah Pack

48 Volt
17-22 Ah Pack

slow rate:
36V 1A
quick rate:
36V 2A

slow rate:
36V 1.5A
quick rate:
36V 3A

slow rate:
36V 3A
quick rate:
36V 6A

slow rate:
48V 1A
quick rate:
48V 2A

slow rate:
48V 1.5A
quick rate:
48V 3A

slow rate:
48V 3A
quick rate:
48V 6A